Factory Defaults

Loaded built-in factory defaults.

Meter Defaults

Built-in factory defaults

Back light ? Green LED ? Red LED ? LCD bias ? Meter serial number ? Measurement mode ? Sleep delay ? Sleep wake delay ? Connected sleep delay ? Connected wake delay ? Mask T4 ? Log raw data ? ADC fault messages ? USB disable ? Reboot to mass storage ? Output by number ?

WiFi

WiFi SSID ? WiFi password ?

WiFi sync time ? WiFi modes ? WiFi enable ? WiFi debug ? WiFi verbose ? IP address ? Static IP string ?

Unrecognised Rows

No unrecognised rows.

Gateways

Up to 10 gateway host/port entries are written to the Gateway CSV row.

Host / IP Port

No gateways defined.

Generated CSV

# BackLight - LCD backlight brightness, as a percentage.
# syntax: BackLight <intensity:percent>
# example: BackLight 12
BackLight 12

# GreenLed - Green LED brightness, as a percentage.
# syntax: GreenLed <intensity:percent>
# example: GreenLed 25
GreenLed 25

# RedLed - Red LED brightness, as a percentage.
# syntax: RedLed <intensity:percent>
# example: RedLed 25
RedLed 25

# LcdBias - LCD bias voltage level.
# syntax: LcdBias <voltage_level:numeric>
# example: LcdBias 63
LcdBias 63

# Serial - Default meter serial number. Use 0 for an unassigned/default template.
# syntax: Serial <serial_number:numeric>
# example: Serial 0
Serial 0

# MeasMode - Measurement mode used by the meter. 0=Rod,1=Clamp,2=RodThenClamp,3=ClampThenRod
# syntax: MeasMode <mode_type:numeric>
# example: MeasMode 0
MeasMode 0

# SleepDelay - Override delay before meter goes to hibernate. Optional wdelay is how often the meter wakes to check battery.
# Times are in seconds. Defaults are sdelay=300, wdelay=1800. Set sdelay to 0 to disable sleep.
# syntax: SleepDelay <sdelay:numeric> [wdelay:numeric]
# example: SleepDelay 0
SleepDelay 0,1800

# ConnectedSleepDelay - Same as SleepDelay, but applies when meter is connected to a USB charger.
# Defaults are 60 seconds (1 minute) and 600 seconds (10 minutes).
# syntax: ConnectedSleepDelay <sdelay:numeric> [wdelay:numeric]
# example: ConnectedSleepDelay 60,600
ConnectedSleepDelay 60,600

# maskt4 - Mask 24 hour pots. Default is 1 (mask) for Portland, 0 for all other sites.
# syntax: maskt4 <0 | 1>
# example: maskt4 0
maskt4 1

# LogRawData - Turn on (1) to log all data read for diagnostics; off (0) otherwise to avoid data loss.
# syntax: LogRawData <0 | 1>
# example: LogRawData 0
LogRawData 0

# AdcFaultMessages - Show transient ADC recovery/fault messages on the LCD. Use 0 for production.
# syntax: AdcFaultMessages <0 | 1>
# example: AdcFaultMessages 0
AdcFaultMessages 0

# WiFi - WiFi settings as SSID,password pairs. Password must be enclosed in double quotes; SSID quotes are optional.
# syntax: WiFi <ssid1:text>,<password1:text> [<ssid2:text>,<password2:text> ...]
# example: WiFi MySSID,"MySecurePassword"
WiFi DummySSID,"DummyPassword"

# Gateway - Gateway server PC to connect to the database, not the IP gateway router.
# syntax: Gateway <server_address:text>:<port:numeric>[,<backup_server:text>:<port:numeric> ...]
# example: Gateway MyServerName.example.com:1957,192.168.221.5:1957
Gateway

# IpAddress - Optional static meter IP address. Leave blank for DHCP. (Prefer use StaticIP)
# syntax: IpAddress <ip_address:text>
# example: IpAddress 192.168.221.123

# USBDisable - Disable USB support when set to 1.
# syntax: USBDisable <0 | 1>
# example: USBDisable 0
USBDisable 0

# WiFiSyncTime - WiFi sync period in seconds. Zero disables periodic checks.
# syntax: WiFiSyncTime <period_seconds:numeric>
# example: WiFiSyncTime 300
WiFiSyncTime 300

# WifiDisable - Set to 1 to disable WiFi.
# syntax: WifiDisable <0 | 1>
# example: WifiDisable 0
WifiDisable 0

# WifiDebug - WiFi diagnostics flag. Turn off (0) when not in use or it may cause data loss.
# syntax: WifiDebug <0 | 1>
# example: WifiDebug 0
WifiDebug 0

# WifiVerbose - Verbose WiFi diagnostics flag. Turn off (0) when not in use or it may cause data loss.
# syntax: WifiVerbose <0 | 1>
# example: WifiVerbose 0
WifiVerbose 0

# RebootToMS - Reboot to mass storage mode when set to 1.
# syntax: RebootToMS <0 | 1>
# example: RebootToMS 0
RebootToMS 0

# OutputByNumber - Nordural CSV output order. Use 1 to output by anode number, 0 by position.
# syntax: OutputByNumber <0 | 1>
# example: OutputByNumber 1
OutputByNumber 1

# WifiModes - WiFi mode flags used by the meter firmware. Bitfield: b0=timed, b1=end-of-pot, b2=on-charger
# syntax: WifiModes <mode_flag:numeric>
# example: WifiModes 3
WifiModes 3

# StaticIP - Optional raw StaticIP value passed to the WiFi library. Comment out to configure with DHCP.
# gatewayIP is the network IP gateway, not the PC server gateway.
# syntax: StaticIP <ip_address:text>[,<gateway_ip:text>,<netmask:text>]
# example: StaticIP "192.168.221.123","192.168.221.10","255.255.255.0"
#IpAddress
#StaticIP "192.168.221.123","192.168.221.10","255.255.255.0"